*UNSORTED

    Fitting central locking pump

    images fitting central locking pump

    Your name or email address: Do you already have an account? As you can see in my pictures its fairly easy to get to, a little rubber strap and the insulation casing falls away allowing you access to the pump. Have you got a signal coming back from the door locks? Now give your key fob a go an see what happens? I can see that with a small relay kit and a solenoid you may be able to open the boot without opening the rest of the car yet to be researched. Things I havent covered: Siren Power windows Trunk Release Siren: I don't know what this does, it may be part of the alarm arming system or sets off the siren to find the car, I don't have any of that and don't need it so I am afraid I don't know. FinleyC1 1 year ago. Another option is to just junk the original system and have the alarm control solenoids in all the doors. I wish i hadn't now as i want to re-install it, but i cant for the life of me remember how it all goes back in Can anyone shed some light on this please? Car theft or car break-ins are always a worry to the motorist and it is wise to take every precaution against them that you can.

  • a4 central locking pump faulty
  • Bert Rowe'sAclass info. Vacuum Pump (central locking)
  • Remote Central Locking Kit Fitting. Forums
  • Volkswagen Golf MK3 Remote Central Locking Upgrade 7 Steps
  • Installing central locking How a Car Works

  • These kits can be fitted to either two-or four-door cars. The kit To convert your car to central door locking you need a kit, which you can readily buy from a car.

    I've just bought a second hand central locking pump for my a3.

    a4 central locking pump faulty

    Does anybody know anything about re-fitting them or about re programming the. You shouldn't have to reprogram the central locking controller if you are replacing the vacuum pump, unless you want to change the options.
    I have wondered about the trunk release, I think it could be used with a solenoid to pop the boot so you dont have to unlock the whole car, my mk6 golf does this.

    Your name or email address: Do you already have an account? While my diagram is the right way round, the first time I did get it the wrong way round.

    Bert Rowe'sAclass info. Vacuum Pump (central locking)

    To lock, the driver door sensor switches the common to the lock wire, and so on. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.

    images fitting central locking pump
    Fitting central locking pump
    It will confuse the pump.

    images fitting central locking pump

    This allows you to lock the car from the outside with a hand-held unit. Some kits are also supplied with a remote control.

    Remote Central Locking Kit Fitting. Forums

    No, create an account now. Car theft or car break-ins are always a worry to the motorist and it is wise to take every precaution against them that you can. First is that the passenger side indicator seems to stay on alittle longer than the drivers sdie when you lock the car. I cut about 2" from the central locking pump motor, doing one cable at a time: cut, strip back, heat shrink on, solder, slide the heat shrink over the solder, heat to shrink - done.

    Please test, with which type of central locking system your vehicle/car is equipped: 1.

    Positive or negative Before installing the door panels again, check the following: 1.

    Volkswagen Golf MK3 Remote Central Locking Upgrade 7 Steps

    Make sure your . connect to pump side of cut wire. Yellow. connect. In the Mk3 Golf as far as I know the central locking pump/module is all located in.

    Video: Fitting central locking pump VW Golf mk3 how to remove central locking pump

    Because of the mounting point of this little module I found I had to extend the. Radio-remote control for central locking system, fitting to VW Golf 3/ Cabrio put the adapter plug between the central-locking pump and the original plug.
    Do the doors on the right hand side operate the locking system at all? As you can see in my pictures its fairly easy to get to, a little rubber strap and the insulation casing falls away allowing you access to the pump.

    Offer up the mounting bracket to the inner door skin. Once you have your cables to length with twisted ends, poke the twisted end in the back of the central locking pump connector in the relevant matched colours as per the wiring diagram.

    images fitting central locking pump

    I tested it plenty of times and it seems to work spot on, with the only odd thing being 1 rear indicator doesnt flash as bright as the rest on unlock, not sure why as it works fine when you go find car!

    images fitting central locking pump
    Fitting central locking pump
    Power Windows: I don't have this feature but I know roughly how this works, its designed for people with electric windows, and acts as a short negative supply to activate the auto roll up my mk6 golf you press and hold for this feature I only have manual winders on my mk3 so don't need it I do have an electric sunroof but I'd need some relay module to shut this as you have to hold the key in position till it shuts!

    No, create an account now.

    Installing central locking How a Car Works

    So it should be a matter of: - Fitting pump back in boot - Fit the actuator with the white base the switch back into driver door you will hopefully still have any original white plastic connecting pieces you need - Fit the slave solenoids in the boot and passenger door. Right wired this in today and have pretty much got it working ok.

    images fitting central locking pump

    Share it with us!


    2 Replies to “Fitting central locking pump”

    1. Grolkree

      I had found that the yellow feed wires to the control box were shorter than most of the rest, so cut the red power wire back to the same length which was a little after its protection fuse. The boot solenoid is the one with the long shaped bit of rod sticking out!

    2. Dainos

      The bit we are interested is in the wiring connector from the central locking pump as it contains everything we need.